Mạch Thu Happymodel Elrs EP2 2.4ghz

Mạch Thu Happymodel Elrs EP2 2.4ghz
Mã SP: Mạch Thu Happymodel Elrs EP2 2.4ghz

315,000 VNĐ

- +

0936.336.128

Địa chỉ mua hàng

Thông tin sản phẩm

Đánh giá nhận xét

The Happymodel 2.4GHz ELRS nano series receiver has an open-source program based on ExpressLRS.

There are three in this series. The PP RX is designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.

On the basis of PP RX, Happymodel has have developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same as PP RX and uses ESP8285 MCU. You can upgrade firmware by WiFi! How simple!

Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. These are very suitable for Tiny whoops because of the ultra-light and Nano size!

Note: This is the EP2_RX Version.

Features

Designed by Jye Smith on the ExpressLRS development team.
TM32L432KBU6 MCU and SX1280 RF chip.
High-refresh-rate RF module
Ceramic Antenna

Specifications

EP2_RX

Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
RF Chip: SX1280IMLTRT RF Module
Minimum receiver refresh rate: 25Hz
Antenna: SMD Ceramic antenna
Dimension: 10mm*10mm*6mm
Firmware Target: aec8ad82
MCU: ESP8285 MCU
Firmware Upload: WiFi
Working voltage: 5v
Weight: 0.44gram
Peak gain: 3.7dB
Type: ISM

Note: Since the official version of ELRS firmware has not been released yet, currently our PP_RX, EP1/EP2 RX, and ES24TX pre-loaded firmware are all beta versions, and you can upgrade the official firmware when the official target is available.

More details
https://github.com/ExpressLRS/ExpressLRS

Binding procedure:

Supply power to the PP/EP1/EP2 RX, wait until the LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the LED light will start to double-flash, which means that the RX enters the binding mode.
Insert the ES24TX module or other DIY 2.4G ELRS TX to Radio transmitter, and choose External RF mode to CRSF protocol, then you can find the ELRS menu from the Radio systems(Need to copy the ELRS.LUA file to the SD-Card tools first), Enter into ELRS and press [Bind], the LED on the RX module will be getting solid if bind is successful.
Receiver LED status meanings:

- PP RX: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no signal connection from the TX module
- EP1/EP2 RX: LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no signal connection from the TX module; LED flash fast means in WIFI hotspot mode, you can connect the WIFI of the RX and upgrade the firmware of the RX via visit 10.0.0.1 from the web browser(password: expresslrs)

Includes

1x Happymodel ExpressLRS Nano 2.4GHz EP2 RX
1x Clear Plastic Heat Shrink

Xem thêm

TẠI SAO BẠN NÊN CHỌN CHÚNG TÔI

Thương hiệu lâu năm, 1 trong những cửa hàng lâu đời nhất còn đang tồn tại và phát triển.
Sản phẩm chính hãng, đa dạng về chủng loại, giá cả.
Đội ngũ kiến trúc giàu kinh nghiệm, trung thực, tận tâm với khách hàng.
Chế độ hậu mãi hợp lí, cân bằng lợi ích cả 2 bên.
Vận chuyển miễn phí cho khu vụ nội thành với đơn hàng trên 2 triệu đồng.
Kiểm tra hàng, thanh toán tại nhà khi nhận hàng.