Mạch Bay Happymodel CrazyF405HD 12a ELRS 1-2S AIO
Mã SP: Mạch Bay Happymodel CrazyF405HD 12a ELRS 1-2S AIO

  • 1,370,000 VNĐ
  • Số lượng:
    - +

    0936.336.128

    Thông tin sản phẩm

    Đánh giá nhận xét

    Only the v1.0 version of the CrazyF405 flight controller has silk screen printing errors, and the V1.1 and V2.0 versions have been fixed

    A flight controller with a built-in Serial ELRS receiver and 4-IN-1 Blheli_S 12A ESC specially developed for Digital HD FPV, which removes the analog OSD chip 7456, optimizes the PCB layout, and supports 1-2S Lipo/LiHV lithium batteries, very Suitable for Digital HD Tinywhoop/Cinewhoop/Toothpick and other small FPV drones. The flight controller uses the F405 chip, supports Betaflight/INAV firmware, has 3 sets of complete UARTs available, and integrates a BMP280 barometer and 8Mbp blackbox, which greatly enhances the playability of the flight controller.

    Specifications:
    Brand Name: Happymodel
    Item Name: CrazyF405HD ELRS 1-2S AIO Flight controller
    Mount size: 25.5mmx25.5mm
    Weight: 4.8g without power lead wire
    Firmware target: BetaflightF4
    Support 1-2s Lipo/LiHV battery

    Flight controllerMCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
    GYRO Sensor: BMI270  (SPI connection)
    Mount hole size: 25.5mm*25.5mm
    Power supply: 1-2S battery input (DC 2.9V-8.7V)
    Built-in 12A(each) Blheli_S 4in1 ESC
    Built-in Serial ExpressLRS 2.4GBuilt-in BMP280 Barometer
    Built-in 8MBp blackbox
    Built-in voltage meter sensor , voltage meter scale 110Built-in current meter sensor , current meter scale 470
    Onboard 4in1 ESCPower supply: 1-2S LiPo/LiPo HV
    Current: 12A continuous peak 15A (3 seconds)
    Support BLHeli_S Bluejay firmware
    Factory firmware: Bluejay ESC V0.19Firmware target: Z-H-30
    Default protocol: DSHOT300
    When use 1s battery and high KV 0702/0802 motors, should set startup power to 1100/1200
    Onboard UART ExpressLRS 2.4GHz ReceiverPacket Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
    RF Frequency: 2.4GHz
    Antenna: enameled copper wire 31mm length
    Telemetry output Power: <12dBm
    Default firmware version: ExpressLRS V3.0.1
    Firmware target: HappyModel EP1/2 2400 RX
    Could update firmware via ExpressLRS configurator

     

    For original factory 4.3.2 version firmware, if you want to use BMP280 barometer, please connect to betaflight configurator and then move to CLI command, then type the following command:

    resource I2C_SCL 2 B10
    resource I2C_SDA 2 B11
    set baro_bustype = I2C
    set baro_i2c_device = 2
    save
     
    If you upgrade the firmware to 4.4.2 and want to use BMP280 barometer, please add BPM280 support to custom defines, following the procedure:
    1. Enable expert mode on firmware flasher tab
    2. Add BARO_BMP280 to custom defines
    3. Flash the board
    4.Configure resources for external BARO device for the flight controller in CLl:
     
    resource I2C_SCL 2 B10
    resource I2C_SDA 2 B11
    set baro_bustype = I2C
    set baro_i2c_device = 2
    save
    Xem thêm

    TẠI SAO BẠN NÊN CHỌN CHÚNG TÔI

    logo

       

      • Thương hiệu lâu năm, 1 trong những cửa hàng lâu đời nhất còn đang tồn tại và phát triển.
      • Sản phẩm chính hãng, đa dạng về chủng loại, giá cả. 
      • Đội ngũ kiến trúc giàu kinh nghiệm, trung thực, tận tâm với khách hàng.
      • Chế độ hậu mãi hợp lí, cân bằng lợi ích cả 2 bên. 
      • Vận chuyển miễn phí cho khu vực nội thành với đơn hàng trên 2 triệu đồng.
      • Kiểm tra hàng, thanh toán tại nhà khi nhận hàng.

       

    Hotline: 0936.336.128
    Để lại lời nhắn cho chung tôi